« Back To Robotics Case Studies
Kawasaki Robotics (USA), Inc. Logo

Member Since 1987


With more than 210,000 robots installed worldwide, Kawasaki is a leading supplier of industrial robots and robotic automation systems with a broad product portfolio, able to service a wide range of applications across diverse industries. Kawasaki has incorporated 50 years of experience as a robot industry leader into the development of the most technically advanced controllers and the highest quality robots. Kawasaki Robotics (USA), Inc. is a subsidiary company of Kawasaki Heavy Industries, L

Content Filed Under:

Metals and Off Road/Heavy Equipment Metals and Off Road/Heavy Equipment

Material Handling and Other Material Handling and Other

Case Study: Kawasaki Robotic Tube Bending Increases Throughput and Eliminates Safety Risks

POSTED 05/22/2019  | By: Lilly Keyes, Kawasaki Robotics, Marketing Specialist

Robotic machine tending can offer a wide range of benefits, whether it is ergonomic relief, increased throughput, or a more streamlined and efficient process overall.  For Kawasaki Motors Manufacturing Corp., USA (KMM), automation helped them in all of these areas.

Five years ago, KMM installed their first tube bending cell using Kawasaki R series robots, called Bender Bot 1, to bend pipes for all-terrain vehicle (ATVs) and four-wheeler frames.  Since the implementation of Bender Bot 1, they have installed another tube bending cell, aptly named Bender Bot 2, and they are hoping to install a third Bender Bot cell in the near future.


  • Eliminate safety risks posed by heavy pipe loading
  • Increase throughput for the bending of smaller pipes
  • Streamline the post-bending process
  • Design a reliable process for weld seam alignment
  • Create an easy-to-program system to accommodate product changes

An Ergonomic Challenge

Over time, KMM’s vehicles grew in size to meet the demands of the market.  Before installing Bender Bot 1, the company’s manufacturing process required an operator to handle 10-ft long pipes weighing up to 20 lbs over the course of an 8 hour shift, while ensuring the weld seam was loaded perfectly.  This precise, repetitive motion involving such heavy, cumbersome objects posed an obvious risk of injury for the operators.

Speed Up Production

As production goals increased, KMM needed a solution that would allow them to speed up the process of bending their smaller, lighter tubes without additional labor or compromising product quality.

Accuracy is Crucial

Many of the roughly 65 tube configurations require the bending of round tubes.  If the round tube isn’t placed in the bending machine at a near-perfect angle or even rolls slightly from the required weld seam position, the tube could stretch or shrink, which distorts the shape of the tube and creates waste through rejection.  KMM needed a solution that put accuracy first, which meant it was imperative that they use robots they could count on.  “Kawasaki roots are known in the industry for their reliability,” Chief Engineer Scott Gordon said.  Kawasaki RS020N and RS050N robots have a repeatability of ±0.04 mm and ±0.06 mm respectively which, when paired with the Laser Seam Finder, results in the consistency KMM needed for a quality end product.


After seeing the potential for operator injury, Gordon designed Bender Bot 1 to eliminate this risk.  The cell uses one Kawasaki RS050N robot to unload the pipes from the Laser Seam Finder, which sets the tubes in the ideal weld seam position for the robot to pick up.  The robot then picks the heavy pipes one at a time and loads them into the tube bending machine.  Once the pipe has been bent, the robot unloads them onto a custom rack. This process allowed the manufacturer to minimize the amount of heavy lifting done by operators, allowing them to shift their focus to running programs and overseeing the process as a whole.

With the positive effects of Bender Bot 1 for large, heavy pipes, KMM decided to install another tube bending cell to handle the smaller, lighter pipes, but with a different goal.  This cell would be focused on increasing throughput, so it uses two Kawasaki robots – one to unload pipes from the Laser Seam Finder and load them into the tube bending machine, and another to retrieve the finished pipe and load it onto the custom pipe cart.

Both cells use a proprietary Laser Seam Finder, which was also designed by Gordon.  This highly accurate machine is used to make sure the weld seam is in the proper location when the robot picks it up to place in the tube bender.  Here’s how it works: A tiny notch is cut in the round pipes.  The Laser Seam Finder rotates the pipe in front of a Cognex camera until it notices the notch.  This machine can get within 1.5° of the notch – a point that is critical in this process, especially when the pipes have special features such as rivet holes or shaped ends.  For pipe with straight cut ends, a color sensor is used to detect the weld seam.  If the weld seam is even 5° off for these specialty pipes, it could cause the pipe’s features to shift and make for a defective product down the line.  This machine, paired with the reliability of Kawasaki robots, allowed KMM to eliminate human error and drastically decrease the amount of scrap they were producing while seeing a consistent product quality.


  • Operators’ heavy pipe lifting stress is reduced to one lift per pipe, as opposed to two
  • The Loader/Seam Finder load height is lowered to waist level, which is an ergonomic improvement
  • Robotic cells increased production
  • Time freed by Bender Bots 1 & 2 allowed operators to take on additional work
  • Loader/Seam Finder has up to 1.5° accuracy for weld seam finding

After implementing Bender Bots 1 and 2, KMM saw an increase in production in two ways. Bender Bot 1 allowed for non-stop production during an 8 hour shift – before automation, the operator would have to stop production repeatedly to inspect pipe, manage pipe carts, and go to break, lunch or shift change.  Now, Bender Bot is able to continue running while the operator is performing these tasks, and the operator is able to take on additional tasks.

The Bender Bot cells also gave KMM the versatility they were looking for.  “Our equipment isn’t dedicated to any one part,” Gordon said.  “The more flexible the system is, the more we can change things around as new models come in and new models get older.”

All components of the Bender Bot – the Laser Seam Finder, Kawasaki robots, tube bending machine and pipe carts – are all connected by Ethernet.  The Tube Bender is the master, which makes it easy for the operator – they call up one program, and all of the machine components receive that program number, adjust and cross check automatically.  This gives the operators more time, so they’re able to run specialty pipes through a die press prior to loading into the Laser Seam Finder.  Before automation was needed, this process was done by different operators in another area of the building.  This role consolidation was an unexpected benefit that KMM didn’t take into consideration when they implemented Bender Bots 1 and 2, but had a big impact on their overall efficiency.

After five years of robotic tube bending, KMM has refined their process so it’s versatile and practical.  The robots unload the bent pipes into custom racks made for each specific configuration, so the carts can be wheeled to the Kawasaki robotic arc welding cells, where they attach for loading into the next step in their manufacturing process.

Current State

KMM bends 700 pipes/hour using Kawasaki robots.  Currently, 33% of KMM’s pipe bending processes are automated, but they’d like that number to increase – they are looking to add a Bender Bot 3 in the next year.  Over the past 5 years, KMM has met their ROI for both cells, and has seen improvements across the board – some they weren’t even expecting.